Casa> Elenco prodotti> Pompa di liquame orizzontale> Pompe di alimentazione ZJW> Pompe di alimentazione per macinazione del mulino
Pompe di alimentazione per macinazione del mulino
Pompe di alimentazione per macinazione del mulino
Pompe di alimentazione per macinazione del mulino
Pompe di alimentazione per macinazione del mulino
Pompe di alimentazione per macinazione del mulino
Pompe di alimentazione per macinazione del mulino

Pompe di alimentazione per macinazione del mulino

$5000≥1Set/Sets

Tipo di pagamento:L/C,T/T,Paypal,Money Gram,Western Union
Incoterm:FOB,CFR,CIF,EXW,FAS,FCA,CPT,CIP,Express Delivery
Quantità di ordine minimo:1 Set/Sets
Trasporti:Ocean,Land,Air,Express,Express
Porta:Tianjin,Qingdao,Guangzhou
Caratteristiche del prodotto

Modello65ZJW

marchioNaipu

TypeClay Wet Sand

Casting MethodThermal Gravity Casting

Sand Core TypeClay Sand Core

ApplicationMachinery Parts

MachiningBoring Machine

MaterialSteel

Surface TreatmentSand Blast

Surface RoughnessRa0.4

StandardGB

CertificationISO 9001:2008

65ZJW Feeding Pumps65

Confezionamento e consegna
Unità vendibili : Set/Sets
Tipo pacchetto : Scatola di legno
Esempio immagine :
Descrizione del prodotto

65 zjw pompe di alimentazione filtro pressa

Sbalzo orizzontale centrifuga liquame pompe / pompe gomma liquami foderato / pompe R55 liquami / pompe premistoppa liquami / pompe guarnizione centrifuga liquami / usura pompe resistente liquami gomma / pompe slurry intercambiabile / pompe Lavaggio del carbone liquami / Sabbia e pompe ghiaia movimentazione liquami / trattamento degli effluenti slurry pompe / pompe minerali elaborazione flottazione / pompe di lavaggio carbone / alimentazione pompe


Filtro serie di pompe di alimentazione pressa Naipu® NP-ZJW accetta DESIN ed installazione modalità idraulico unico del

girante, assicurarsi che la sua curva caratteristica della pompa sia più ripida rispetto alle pompe normali, è più adatto da utilizzare nella

alimentazione filtro pressa varia a seconda delle variazioni della resistenza per realizzare la grande capacità,

alimentazione a bassa pressione e bassa capacità, alta pressione pompa filter.The è ampiamente usato in laveria carbone,

la tutela ambientale, fabbrica di alluminio, fonderia, ecc



Disegno di costruzione

drawing-1





La tabella di struttura della pompa di alimentazione

1.Two fase voluta 2.Two fase girante

3.One-fase piastra voluta 4.Back

camera 5.Feeding 6.Locating cespuglio

piastra di copertura 7.Expeller 8.Expeller

9.Decompression corpo 10.One fase girante

11.Tie bar manicotto 12.Shaft

piastra 13.Cover anello 14.Disassembly

15.Water piastra di supporto 16.Bearing

manicotto 17.Shaft 18.Bearing spacer

19.Bearing copertura 20.Frame

tubo 21.Bent



NP-ZJW POMPA TABELLA DI SCELTA

selection chart



NP-ZJW Pompa di alimentazione PARAMETRI DI PRESTAZIONE

Performance Parameters


Panoramica del prodotto:

Filter Press Photos


Possibili errori e gli insediamenti.


        Faults

    Reason

      Settlement

1.Pump fails to discharge any water,The hand of pressure gauge beat violently

1.Suction pipe don`t have enough water.

2.Suction pipe blocked or the valve is locked.

1. Inject enough water

2.unlock the inlet valve,clear the blocks

3.Exclude the air leakage

2.The pump can`t discharge water,the hand of vacuum meter beat heavily.

1.The inlet valve is unlocked or silted up.

2.The resistance of suction pipe is too big or silted up.

3.The height of suction is too high.

1.Unlock the valve or desilting

2.improve the design of  suction pipe or desilt

3.Lower the height of the installation.

3.The pump can`t discharge water,pressure gauge shows heavy pressure.

1.The resistance of the discharge pipe is too big.

2.The impeller blocked

3.The speed is slow.

1.Check and adjust the outlet pipe.

2.Clear the impeller

3. Improve the speed.

4.The pump doesn`t rotate

The volute is silted up by the blocks.

Clear the blocks

5.The capacity is not enough

1.The blocks of the impeller or the inlet or outlet pipe.

2.The abrasion of the impeller is heavily.

3.The speed is low to normal

4.Pump is installed unreasonably or the leakage of the inlet pipe.

5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.

6.The inlet valve not open enough or blocked

7.The packing seal leaks

1.Clear the impeller or pipe.

2.Change the impeller

 

 

3.Adjust the speed

4.Install again or stop leaking.

 

 

5.Decrease the height of the transport or reduce the resistance.

6.Unlock the inlet valve

 

7.Compress the packing tightly

6.The motor of the pump is overloaded

1.The head of the pump exceeds the head of the working condition.

2.Not consider the slurry density when selecting the pump.

3.The packing press tightly

1.Turn down the outlet valve,cut the impeller or lower the speed.

2.Select the motor again.

3.Adjust the the screw of the  packing gland

7.Abnormal sound in the pump, and no water out

1.The resistance of the inlet pipe is too big.

2.The height of the suction is too high.

3.Cavitation occurred

4.there is air in the inlet

5.The temperature of the liquid is too high

1.Clear the suction pipe and sluice valve.

2.Lower the height of the suction

3.Adjust the water valve and let the pump operate in the defined limits.

4.Block the leakage.

5.Lowering the liquid temperature.

8.pump vibrates

1.pump cavitate

2.The block of the impeller single vane

3.The no concentricity  between the pump shaft and motor shaft

4.Fasteners or foundation loose

1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.

2.Clear the impeller

3.Alignment again

4.Fasten the screw,and reinforce the foundation.

9.Bearing is overheat

1.lock the cooling water

2.lubrication is not good.

3.the lubrication oil is not clear

4.the wrong direction of the thrust bearing.

5.there is something wrong with the bearing.

1.Open the cooling water

2.Adjust the oil quantity

3.Clear the shaft,change oil

4.According to the inlet pressure,adjust the direction of the thrust bearing.

5.Change the bearing

10.Packing short life

The material of packing is not good

Change the packing

11.pump leak oil

1.High oil level

2.The rubber parts invalid  

3.Assembly problem

1.Lower the oil level

2.Change rubber spares

3.Adjust the assembly

 

12 Pump head leaking

1.The rubber parts not press well

Assembly again or press tightly 





FAQ:

Q1. Sei un produttore di fabbrica?

Sì, siamo la fabbricazione diretta della fabbrica e hanno più di 10 anni di esperienza in questo settore.

Q2.Do si dispone di prodotti azionari per vendere?

Alcuni ci hanno in magazzino, ma gli altri no. Dal momento che produciamo sempre questi prodotti in base alle esigenze dei clienti.

Q3.What vantaggi avete?

A: Siamo fornitore diretto ed il prezzo è competitivo.

B: Il nostro tecnico sono molto experieced in questo settore, e possiamo fare il servizio OEM per voi.

C: Siamo fabbrica, e possiamo organizzare programma di produzione, in modo da consegna puntuale.


Dettagli del contatto:

Shijiazhuang Naipu Pump Co., Ltd.

Aggiungere: No.368 Xinshi North Road, Shijiazhuang Hi-Tech Industry Development Zone, Hebei, Cina, 050.091.

Tel: 0086-311-897162903

Fax: 0086-311-87162902

Persona di contatto: Karen Tan

Skype: karen_naipump











Casa> Elenco prodotti> Pompa di liquame orizzontale> Pompe di alimentazione ZJW> Pompe di alimentazione per macinazione del mulino
  • Invia domanda

Copyright © 2024 Shijiazhuang Naipu Pump Co., Ltd.Tutti i diritti riservati

Invia domanda
*
*

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Invia